smiffy 99 Report post Posted June 15, 2013 Well I've SORN the GTA the scabby wings are doin me head in so are the pink callipers not good enough for shows... Soooo I'm going to start doing stuff on it. Cambelt and CF2's were done last sept so all good there just Wings New arch liners Re-spray Powdercoat front and rear callipers New of pads New discs front rear Fresh brake fluid Braided hoses Wheel refurb Drivers seat bolster repair Re do engine bay tart up And finally new exhaust Phew Now......I want to most my self to keep costs down, Where's the best place to get arch liners and new wings from or will secondhand ones be ok and get the rust repaired The rest I've got a pretty good idea where to get things from. Will post some before pics tomoz Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 22, 2013 Engine bay as is Started dismantling it today Questions The top engine mount can this be taken off or do I need to support the engine, also the bracket that holds it on to the strut can that be taken off? The cam covers are those ok to be taken off? And when re fitting do they need torquing down? Fuel rails, if I disconnect them will they piss fuel everywhere? Quote Share this post Link to post Share on other sites
Clem Fandango 71 Report post Posted June 22, 2013 Fuel rails will be full but no more will run out. Ohhh get me with all my technical knowledge. Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 22, 2013 Fuel rails will be full but no more will run out.Ohhh get me with all my technical knowledge. Cheers holyman Job for tomorrow Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 22, 2013 need a new induction elbow now, cleaning the old one and found a split Fuck pigs Quote Share this post Link to post Share on other sites
Gaz 29 Report post Posted June 23, 2013 Fuel rails may be pressurised too. Be prepared for a gob full of go juice Quote Share this post Link to post Share on other sites
Smaky 73 Report post Posted June 23, 2013 Yes to all and dont'turn the key if the rails are off. And if you want discounted parts.... Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 23, 2013 Is that a yes to supporting the engine? Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 23, 2013 Key won't turn cus I've disconnected the battery. Quote Share this post Link to post Share on other sites
Smaky 73 Report post Posted June 25, 2013 Is that a yes to supporting the engine? No. Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 25, 2013 Cool thanks Xxxx What torque setting do I need to put the cam covers back on? Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 25, 2013 The air intake elbow has split anyone got a decent spare? Quote Share this post Link to post Share on other sites
Smaky 73 Report post Posted June 27, 2013 Yup. Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 27, 2013 Right? yup your have a spare? How much? Also what torque setting do I need for the cam covers? Quote Share this post Link to post Share on other sites
Smaky 73 Report post Posted June 29, 2013 I'll ceck it's good, and 18 N.m. Quote Share this post Link to post Share on other sites
Smaky 73 Report post Posted June 29, 2013 I'll ceck it's good, and 18 N.m. Although I think you mean coil covers which are just nipped up. Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 30, 2013 No I meant cam covers Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 30, 2013 Some pics of the plug cover, plenum and fuel rails Quote Share this post Link to post Share on other sites
Bigdar 62 Report post Posted June 30, 2013 Looking good so far mate Quote Share this post Link to post Share on other sites
LJ_GQV 115 Report post Posted June 30, 2013 What he said ^^ Quote Share this post Link to post Share on other sites
Gaz 29 Report post Posted June 30, 2013 What did you do to the fuel rails? Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 30, 2013 Need to sand the alfa bit and gta bit but all the gear is at work, waiting for the cam covers to come back. Was gonna do some cleaning on the engine bay today but my head had other ideas Quote Share this post Link to post Share on other sites
smiffy 99 Report post Posted June 30, 2013 What did you do to the fuel rails? Powder coated them in chrome Quote Share this post Link to post Share on other sites
Gaz 29 Report post Posted June 30, 2013 Nice work. I need mine doing after a have sanded all the rustyness off them Quote Share this post Link to post Share on other sites
LJ_GQV 115 Report post Posted June 30, 2013 Instead of sanding them down could you paint them? Either white or try the italian flag on the GTA letters to be difrent? Quote Share this post Link to post Share on other sites