Jump to content

alfapat

Members
  • Content Count

    74
  • Donations

    0.00 GBP 
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by alfapat

  1. Hi to anyone that knows me , still very much with Alfas and not posted for a while I have at present a 156 jtd 16v ;54 plate and might move on to a 159/GT , is it true the 6 speed boxes give the same problems as Vauxhall boxes and are they as much a problem as I keep hearing about them.
  2. Moving on a bit , I found the correct seals for the job , but now I have a problem with the system, Anyone saw this coming ?!! I may not be able to resolve my issue right now as the car leaves me for a couple of months, however I'm keen to resolve this,. what I have done is firstly evacuate the system as I have replaced the condenser. The system has been vacuumed and seems to hold pressure. I filled the so much with refrigerant and then as a caution some leakstop and then finishing with refrigerant. The clutch came in on 35 bar and got to 55 -60 and struggled to consume more than 40-480 g so compressor on all the time but not getting cold. The pressuyre on the other side is basically equalised by the same amount on low side. I am thinking that the compressor is unable to pressurize as the there is little load on the engine when switching fro low to to auto , 147 2.0l by the way. Can anyone help. Cheers Pat
  3. Does anyone know of a source of aircon seals for the 147 , not simple" o" rings, looks like a set of two ribs of rings together.. cheers Pat
  4. Has anyone changed the master cyl. On a 147 jtd., is it relatively straight forward. ---------
  5. Yes I have been leaving it on that, hope fully by the w/e ill get it up high at the front and try a few things.
  6. Does anyone have any magic on how to get my 16v jtdm accept more coolant. I am 2.5 short of what I took out. I have tried tick over and coolant cap off and squeezing rear pipe from thermostat without much luck. Perhaps if I raise the car up high in the front? Cheers Pat
  7. Thanks trying to think too much out of the box, Ordered thermostat
  8. New MAP , not genuine has definitely helped, but not convinced , I have not disconnected MAF yet , its a little bit involved on the 8v as its down under fuse box area and screwed on , so not had time . On a separate issue I have also taken delivery of a 156 sw 1.9jtd 16v and the temperature refuses to rise according to dial. The top hose is not warming up and very little warmth after 25mns . I'm thinking there is a link between the timing belt replacement including water pump and maybe an airlock ?
  9. Many thanks will try that and get back to you.
  10. Ian getting great performance once it hits 1900 revs , so I can't see if that would help , it pulls really well above that , perhaps I'm expecting too much . M y friend had a multipla with the same engine (8v 1.9 jtd) and it was definitely quick to respond at junctions.
  11. I think I can put this down to MAP sensor, I have cleaned it with carb cleaner and I have noticed a marginal improvement. They seam to be very fickle and so I may invest in a new one .
  12. I am stuck with this small but irritating problem with my 1.9 jtd '53 plate 147. Maybe to used to petrols but I have a lack of throttle response from start position , but soon as it hits 1500 revs it shoots off. I have tried cleaning and checking egr , vacuum pipes etc. , what am I missing here?
  13. Hi Alex , thanks for that , excess condensation seems to affect the rear , as the inner sills are always getting water from the front. I an only narrow down the leak to somewhere between the top of the strut housing and its attachment to the bulkhead by a strong plate. However it's inaccessible except by shining a light through the cavity from the bonnet hinge area, where the window washer tubing enters ,and. I can replicate leakage by pointing a running hose over it, or through it. The leak can start just by sitting the car in rain also , it's mad! Im considering blocking off the gap with a plastic plate and silicone. This still leaves a drain to inner wheel arch area free.I have run a hose through this drain for a considerable Time and no leaks to the footwell in that time.
  14. Ok thought I found the reason for wet footwell (3 door 147) drivers, the seam leading down from a drain hole to the right looking from the front near the bonnet hinge and leading down the inner wheel arch . Maybe didn't seal it properly bu still leaking . Also discovered a leak coming from the rear and also ending up in the inner sill.I don't know the source yet but it appears above the rear light fit net and on the inner panel, so somewhere above that? Please some help appreciated , car is closer to scrapping every day!,,,
  15. I have posted this subject on another site and getting nowhere. Exhausted all the usual suspects , water getting into inner sill through the A post somewhere and appearing between the floor and sill at the seam. Trying to remove the front wing off a spare car to see if the fault lies behind it . The car is three door 147 Any help appreciated it's driving me nuts and spoiling. good car. Looking for anyone who has info to resolve this issue please.
  16. Thanks Smaky , changed board, and fine it works . To address the problem of severe damp , I think I ve bought a lemon . The floor was soaked and I think for some time , the rear window loose has been sealed , the windscreen replaced. Long thread on other forum, it is down to a seal somewhere in the door post but can't see where probably behind front wing, it's destroying the car , any suggestions are there crucial seals may have been missed on build , is it obvious when wing is off. Water seeps from inner at joint of floor and sill near post and into floor .
  17. Update, it seems the console with the front fog button on it amounts to others maybe causing the fuse to blow , I have now got the right front fog to work with an alternative console , but I've run out of h1 bulbs , so hopefully , I'm on the right track. í ½í¹‚
  18. Update, it seems the console with the front fog button on it amounts to others maybe causing the fuse to blow , I have now got the right front fog to work with an alternative console , but I've run out of h1 bulbs , so hopefully , I'm on the right track. í ½í¹‚
  19. Are there any known issues with the front fog lights blowing fuses, apart from checking the wiring in the headlight cluster. Not good to do right now as its never stopped raining lately ! Just if anyone has stumbled across anything. 147 '53 jtd😟
  20. Because my front bearing is u/s I'm going to replace it as I've done in the past with a S/H unit which includes the abs sensor unit. I have waiting in the wings a 147 2.0 l with a white abs plug , it's important the the colour of this plug as I think all the 2.0l 147 and 156 should be the same up to the later new headlight model , sorry haven't progressed to that year so I'm asking the question really is the only difference to swap complete hubs is to match ABS versions of plugs as the sensors are different lengths due to the bearings being different. Can anyone clarify this please.
  21. Hmm should have changed the larger vertical bush at the time , didn't recognize the part at the time was available , never mind not doing again at the moment.
  22. Your correct Smaky , so replaced side bush and couldn't find vertical bush on the gearstick but put it all together not realising I had seen the part earlier , things were not easy to reassemble , however its all done and the gearshift has a dramatic improvement after realising that the shaft ontop of the gearbox was partially seized as well , so accelerating the wear on the side bush. Not for a job on your own , needs a little help from friend. Neither bush expensive.
  23. Let me say for a rotten gear change, to go and repair this is a pig of a job , all for the sake of a very small plastic bush ------------ Only Alfa would manage something like this to go wrong , don't get me wrong , I love them!Im sure it will improve things on the gearchange front as it' s hellish at the moment Only thing is having gone this length to remove the gearstick and components shear some four rusty bolts etc. and not replace the vertical bush which is also a puzzle to remove cause you have to to get the small bush out to replace. It seems a risk as although it doesn't have the play /wear that the side bush has its silly not to replace. So if anyone can tell me or know if its replaceable then please let me know .
  24. Just found this post from Smaky "It will be te small cup which fits in from underneath being worn, or worse the gearstick mounting being cracked, not the end of the world but the exhaust and center tunnel need to be dropped to replace either, merely a few hours work " Sounds like more hours than a few , any favourite places to source this part before I dismantle please?
×
×
  • Create New...